PLUMBING BASICS: THE FIRST STEP FOR BATHTUB INSTALLATION

Plumbing Basics: The First Step for Bathtub Installation

Plumbing Basics: The First Step for Bathtub Installation

Blog Article

Information Here

This post following next pertaining to How to Install a Bathtub: Install an Acrylic Tub and Tub Surround is highly fascinating. Read it yourself and figure out what you think about it.


A Step-by-Step Guide to Installing a Bathtub
Mounting a bathtub isn't precisely rocket science, yet it does need strong plumbing, carpentry, as well as occasionally, tiling skills. Replacing an old tub with a brand-new one is additionally a moderately difficult project. If the old tub is readily available, the task can move immediately; if you have to open up a wall to get rid of the old bathtub and position the brand-new bath tub, the job is a lot harder. In either situation, the project is within a house handyman's skills, although you will certainly need a helper to vacate the old tub as well as set in the brand-new one. Make certain you have certified yourself for the work and also fit trying it. As opposed to hiring a specialist to take control of a halfway-completed task, it is better to think about using one prior to you start. Chances are you might need a professional plumber to make tube connections.
This post will aid you install a new tub in your bathroom if you have already bought a brand-new bathtub and do not need to transform the setup of your previous water supply pipelines.
Your devices as well as product list ought to comprise the following:
  • New Tub

  • Hammer

  • Pipeline Wrenches

  • Prybar

  • Safety Glasses

  • Degree

  • Pliers

  • Adjustable Wrench

  • Putty Blade

  • Screwdriver

  • Cold Knife

  • Measuring tape

  • Pipe Caps


  • Removing Old Touches


    If you require to replace old taps with brand-new ones as a part of your installation, after that the first thing you should do is detach the water. After doing so, turn on the taps to drain pipes any kind of water staying in the system. The process of eliminating the existing faucets can be quite troublesome because of the restricted access that is frequently the situation.
    Utilize a container wrench (crowsfoot spanner) or a tap tool to undo the nut that links the supply pipelines to the faucets. Have a fabric prepared for the staying water that will certainly originate from the pipelines. As soon as the supply pipelines have actually been gotten rid of, use the exact same tool to loosen up the nut that holds the faucets onto the bath/basin. You will certainly need to quit the solitary faucets from turning during this procedure. When the taps have actually been eliminated, the holes in the bath/basin will need to be cleaned up of any kind of old sealing compound.
    Prior to carrying on to fit the brand-new taps, compare the pipe links on the old taps to the brand-new taps. If the old faucets are longer than the brand-new faucets, after that a shank adapter is required for the new faucets to fit.

    Suitable New Taps


    If the tails of the new taps are plastic, then you will certainly need a plastic connector to prevent damage to the string. One end of the port fits on the plastic tail of the tap and also the various other end gives a connection to the current supply pipes.
    If you need to fit a monobloc, after that you will need decreasing couplers, which links the 10mm pipe of the monobloc to the typical 15mm supply pipe.
    Next, position the tap in the installing hole in the bath/basin guaranteeing that the washing machines are in area in between the faucet as well as the sink. Safeguard the faucet in position with the supplier given backnut. When the faucet is safely in position, the supply pipelines can be connected to the tails of the taps. The taps can either be attached by using corrugated copper piping or with regular faucet connectors. The former kind ought to be linked to the faucet ends initially, tightening up only by hand. The supply pipelines can later on be connected to the various other end. Tighten both ends with a spanner after both ends have actually been attached.

    Mounting the Bath tub


    Utilizing both wooden boards under its feet, place the tub in the needed position. The wooden boards are valuable in uniformly spreading out the weight of the tub over the location of the boards rather than focusing all the weight onto four small points.
    The following goal is to ensure that the bathtub is leveled all round. This can be accomplished by examining the level and changing the feet on the bath tub till the spirit level reads degree.
    To set up taps, fit the bottom of the outermost flexible tap adapter to the proper supply pipeline by making a compression sign up with; then do the exact same for the various other tap.
    Switch on the water system as well as examine all joints and new pipework for leaks as well as tighten them if required. Fill the bathtub as well as additionally check the overflow electrical outlet as well as the normal electrical outlet for leaks.
    Ultimately, deal with the bath paneling as explained in the maker's instruction manual. Tiling as well as sealing around the tub needs to wait until the bath tub has been utilized at the very least when as this will certainly resolve it into its final placement.

    Preparing for the Installation


    Firstly, the sustaining framework provided with the bathroom must be fitted (if required) according to the producer's directions. Next, fit the taps or mixer to the bath tub. When fitting the faucet block, it is very important to make sure that if the faucet includes a plastic washing machine, it is fitted in between the bathroom and the taps. On a plastic bathroom, it is likewise sensible to fit a sustaining plate under the taps unit to stop stress on the bath tub.
    Fit the adaptable tap adapters to the bottom of both taps using 2 nuts and olives (occasionally provided with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet opening, and then pass the electrical outlet through the hole in the bath. Utilize the nut provided by the producer to fit the plug-hole. Check out the plug-hole outlet for an inlet on the side for the overflow pipe.
    Next, fit completion of the adaptable overflow pipeline to the overflow outlet. After that, screw the pipeline to the overflow face which should be fitted inside the bath. See to it you make use of all of the supplied washers.
    Link the catch to the bottom of the waste electrical outlet on the bathtub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the trap to the outlet. Connect the bottom of the overflow tube in a similar manner.The bath should currently prepare to be fitted in its last setting.

    Tiling Around the Bathtub


    In the area where the bath satisfies the tile, it is essential to secure the accompanies a silicone rubber caulking. This is very important as the installation can relocate sufficient to crack a rigid seal, causing the water to permeate the wall between the bath and the tiling, resulting in problems with moisture and possible leakages to the ceiling listed below.
    You can pick from a range of coloured sealants to blend in your components and also installations. They are offered in tubes and cartridges, and also can sealing voids as much as a width of 3mm (1/8 inch). If you have a bigger space to load, you can load it with twists of drenched newspaper or soft rope. Bear in mind to always fill up the bathtub with water before securing, to allow for the movement experienced when the bathtub is in use. The sealer can fracture relatively early if you do not take into account this motion before securing.
    Conversely, ceramic coving or quadrant floor tiles can be used to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and reduce to dimension, are additionally quickly available on the marketplace. It is a good idea to fit the tiles using waterproof or water-proof glue as well as cement.

    A Step-by-Step Guide to Installing a Bathtub


    Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.



    But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.



    This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.


    Remove the Existing Bathtub


    To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.



    The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.


    Choose the Right Bathtub


    The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.


    Install the Plumbing and Ledger Board


    You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.



    Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.


    Install the Bathtub


    When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.



    Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.



    If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.


    Hook up the Plumbing


    Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.


    Install the Bathtub Surround


    A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.



    Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.



    If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.



    If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.

    https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/


    A Step-by-Step Guide to Installing a Bathtub

    I was shown that article about How to Install a Bathtub through someone on our other website. Sharing is nice. You never know, you may just be helping someone out. I am grateful for your time. Please visit our blog back soon.


    Tap issues? Ring!

    Report this page